- True 2", 3" & 4 inch lift without travel restricting lift rods
- Keeps suspension in factory geometry and thus more likely to keep your suspension warranty intact.
- Lifts the entire body/chassis off the suspension system subframe so in the unlikely event your bags do fail your still your chosen lift higher above your tires always.
- Drops all diffs, suspension and steering componentry and keeps them working as the factory intended.
- Keeps all the unsprung weight of entire subframe systems low, lift rods don't do this.
- A solid engineered system built to last and proven on many other new generation land rovers, extensively tested in Moab and Australia
- With the right tires and offset, drives and acts very close to how the factory intended even at 6inch lift.
- Full factory down travel, with the combined body/chassis 2, 3 or 4 inches higher.
- It's the best of the best new defender Suspension lifts with no downsides.
- Patented System by J A Fab.
- All lift parts have been carefully designed to avoid corrosion with the aluminum vehicle structure.
- You can add lift rods(not recommended) or software lifts/drops(temporary height change sold separately) on top of this if you want, allowing a 4,5 or 6 or 8 inches+ lift over factory new defender ride height, and an additional 3 inches on top of those figures on-demand to get over obstacles (with elift super-extended mode)
- For the ultimate system, we recommend a combination of software lifting plus subframe lifting. Then you can lift to get over obstacles above the subframe height and return to your chosen subframe height, plus drop your height suspension down for on-road as needed, contact us for more details. (elift or Gap module sold separately on NDM website)
- Keeps suspension bags at a height factory did not intend fulltime.
- Possible issues with suspension and geometry being at a height factory did not intend all of the time
- Uncomfortable ride all the time the higher the rods especially offroad.
- Solid style lift rods can lead to height sensor issues as factory height sensors are highly flexible for a reason, to protect the sensors in case of impact.
- Loose down travel, every inch you lift using rods you lose that in down travel
- Suspension tops out when four-wheel driving in high mode, producing audible and uncomfortable clunking and its worse the highed the lift.
- Suspension geometry is affected when using lift rods away from factory perfect settings
- If you run bigger tires, if suspension fails you end up on the tires stuck with no way out, cant even tow.
- Due to the above, we no longer recommend or endorse lift rods to anyone, especially 2inches
More Information On Subframe Lifts
Suits 90, 110 and 130 coil or air suspension ( Defender 90 will need a double cardon rear drive shaft fabricated)
Kits are generally built to order due to the high cost of parts in the kits however if it says in stock for the product variant its instock.
Left or right-hand drive and engine model must be provided in order notes or emailed after. (If these details or VIN are not provided we will contact you)
The 2" New defender Kit is our recommended height 32-34s (35s can work with cooler relocate and trimming and correct ET wheels)
3" we recommend 35" tires with our cooler tilting kit and trimming
4" we recommend for 35s-36s (37s possible with work)
5" and 6"inch 37s-38s (avail on request email or msg us)
Cooler tilting (part sold separately on NDM website) and fender plastic trimming mods may be needed for the larger tires.
We cover other new Landrover models including 2-4inch for 5 or 6imch or RRS and full-size RR please email us via ops@newdefendermods.com for more info.
Important
Only a selection of parts are shown in the images attached, for example from the 2inch lift ( it comes with 36 Individual Lift parts plus fixings). 4 and 5/6-inch kits come with many more parts on top of these.
Ships From
Express from USA
Checkout shipping rates
Worldwide
International Shipping Insurance included!
Lead Time
4" - approx 7 lead